Enrique Romero Pascual

@article{Romero2021,

title = {Moodle and Socrative quizzes as formative aids on theory teaching in a chemical engineering subject},

author = {E. Romero and L. García and J. Ceamanos},

doi = {10.1016/j.ece.2021.03.001},

issn = {17497728},

year  = {2021},

date = {2021-01-01},

journal = {Education for Chemical Engineers},

volume = {36},

pages = {54-64},

keywords = {},

pubstate = {published},

tppubtype = {article}

}

@article{nokey,

title = {Nanosheets of MIL-53(Al) applied in membranes with improved CO2/N2 and CO2/CH4 selectivities},

author = {Adelaida Perea-Cachero and Javier Sánchez-Laínez and Beatriz Zornoza and Enrique Romero-Pascual and Carlos Téllez and Joaquín Coronas},

doi = {10.1039/C8DT03774D},

issn = {1477-9226},

year  = {2019},

date = {2019-01-01},

journal = {Dalton Transactions},

volume = {48},

issue = {10},

pages = {3392-3403},

abstract = {<p> Nanosheets obtained from MOF MIL-53(Al) applied in mixed matrix membranes with improved CO _{2} /N _{2} and CO _{2} /CH _{4} selectivities. </p>},

keywords = {},

pubstate = {published},

tppubtype = {article}

}

@article{nokey,

title = {Enhancement of Growth of MOF MIL‐68(Al) Thin Films on Porous Alumina Tubes Using Different Linking Agents},

author = {Adelaida Perea‐Cachero and Pablo Calvo and Enrique Romero and Carlos Téllez and Joaquín Coronas},

doi = {10.1002/ejic.201700302},

issn = {1434-1948},

year  = {2017},

date = {2017-01-01},

journal = {European Journal of Inorganic Chemistry},

volume = {2017},

issue = {19},

pages = {2532-2540},

abstract = {<p>The preparation of MIL‐68(Al) films on the inner surface of alumina tubes is reported. As the direct deposition of the MOF on bare alumina gives poor adhesion results, three different linking agents are employed to achieve a good MOF–support interaction. Colloidal silica LUDOX®, zeolite silicalite‐1, and natural polysaccharide chitosan are chosen as binders, because they contain potential functional groups (hydroxy, amino, ether), which can establish hydrogen bonds. While colloidal silica leads to noncontinuous MOF layers, silicalite‐1 and chitosan give rise to uniform and well‐anchored films, as confirmed by the different characterization techniques used to study the MOF layer. Single‐gas permeation experiments are carried out to determine the quality and ideal efficiency of the membranes prepared with silicalite‐1 and chitosan. The results for the MIL‐68(Al)/silicalite‐1 membranes evidence the existence of macrodefects. However, no cracks are found when chitosan is used as a linking agent, and the gas flow through the MIL‐68(Al)/chitosan membranes clearly follows Knudsen diffusion.</p>},

keywords = {},

pubstate = {published},

tppubtype = {article}

}

@article{nokey,

title = {Modelling of an HTPEM-based micro-combined heat and power fuel cell system with methanol},

author = {E. Romero-Pascual and J. Soler},

doi = {10.1016/j.ijhydene.2013.07.015},

issn = {03603199},

year  = {2014},

date = {2014-01-01},

journal = {International Journal of Hydrogen Energy},

volume = {39},

issue = {8},

abstract = {A fuel cell-based combined heat and power system using a high temperature proton exchange membrane fuel cell has been modelled. The fuel cell is fed with the outlet hydrogen stream from a methanol steam reforming reactor. In order to provide the necessary heat to this reactor, it was considered the use of a catalytic combustor fed with methanol. The modelling aims to fit the hydrogen production to the demand of the fuel cell to provide 1 kWe, maintaining a CO concentration always lower than 30,000 ppm. A system with 65 cells (45.16 cm2 cell area) stack operating at 150 C and hydrogen utilization factor = 0.9 (with O2/methanol ratio = 2 at combustor; H2O/methanol ratio = 2 and temperature = 300 C at reformer) needed a total methanol flow of 23.8 mol h-1 (0.96 L h-1) to reach 1 kWe, with a system power efficiency (LHV basis) ca. 24% and a CHP efficiency over 87%. The ability to recycle the non-converted hydrogen from the fuel cell anode to the combustor and to use the heat produced at the fuel cell for obtaining hot water increased the global energy efficiency. Copyright © 2013, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.},

keywords = {},

pubstate = {published},

tppubtype = {article}

}